PhaseWorks

Gases, liquids and solids: gas laws, ideal gas law, partial pressures, kinetic theory, intermolecular forces, phase diagrams and unit cells.
Read the idea in Learn, then practise. Each tab has Hint, Reset and Skip, 3 levels and a crown to win.

Track 1 · General Chemistry I · part of ChemTracks

Start here: matter in its three states

Gases, liquids and solids differ in how strongly their particles attract each other compared with how fast they move. In this track you will predict how a gas responds to changes in pressure, volume and temperature, do calculations with gases in reactions, and explain the properties of liquids and solids from the forces between particles.

Want to explore freely first? Open GasLabs: move the piston, heat the gas, add moles, and record your own data.

Build it, test it, own it

Read the idea in Learn, then practise it. Every tab has Hint, Reset and Skip, 3 levels, and a crown to win. You never need to memorize: you will see each idea again and again until it is yours.

Always use kelvin

Gas-law temperatures must be in kelvin: K = °C + 273.15. Convert pressure units with 1 atm = 760 torr = 101.325 kPa. R and the tables are in the toolbox.

Map of this tool. Steps 1 to 4 are gases. Step 5 explains why gases behave as they do. Steps 6 to 8 move to liquids and solids: intermolecular forces, vapor pressure and phase diagrams, then crystal structure.

Step 1. The gas laws

For a fixed amount of gas: Boyle P1V1 = P2V2, Charles V1/T1 = V2/T2, Gay-Lussac P1/T1 = P2/T2. They combine into P1V1/T1 = P2V2/T2. Avogadro: V is proportional to n.

Worked example. 5.00 L of gas at 1.00 atm and 20 °C is compressed to 2.00 atm and heated to 80 °C. V2 = 5.00 × (1.00/2.00) × (353/293) = 3.01 L.

Step 2. The ideal gas law

PV = nRT, with R = 0.08206 L·atm/(mol·K). Rearrange for molar mass M = mRT/(PV) and density d = PM/RT. At STP (0 °C, 1 atm), 1 mol of ideal gas has a volume of 22.41 L.

Worked example. Density of CO2 at 1.00 atm and 25 °C: d = (1.00 × 44.01) ÷ (0.08206 × 298.15) = 1.80 g/L.

Step 3. Gas stoichiometry

Add the gas law to the mole road map: g reactant → mol reactant → mol gas → V by PV = nRT. At constant T and P, volumes of gases are in the ratio of the coefficients.

Worked example. 2 KClO3 → 2 KCl + 3 O2. 12.25 g KClO3 is 0.100 mol, which gives 0.150 mol O2, or 0.150 × 22.41 = 3.36 L at STP.

Step 4. Mixtures of gases: Dalton’s law

Ptotal = Σ Pi, and Pi = χi Ptotal where χ is the mole fraction. For gas collected over water, Pgas = Patm − PH2O.

Worked example. H2 is collected over water at 25 °C and 755 torr (PH2O = 23.8 torr): P(H2) = 755 − 23.8 = 731 torr.

Step 5. Kinetic theory, effusion and real gases

The average kinetic energy of gas particles is proportional to T and is the same for every gas at the same temperature. So lighter molecules move faster: urms = √(3RT/M), and Graham’s law gives effusion rates in the ratio √(M2/M1). Real gases deviate from ideal behavior at high pressure and low temperature, where particle volume (b) and attractions (a) matter.

Worked example. H2 effuses √(32.0/2.016) = 3.98 times faster than O2.

Step 6. Intermolecular forces

Every molecule has London dispersion forces (bigger molecules, stronger forces). Polar molecules add dipole–dipole forces. Molecules with H bonded to N, O or F hydrogen bond, the strongest of the three. Stronger forces mean higher boiling points, viscosity and surface tension, and lower vapor pressure.

Worked example. H2O (373 K) boils far above H2S (213 K) because water hydrogen bonds and H2S does not.

Step 7. Vapor pressure, phase changes and phase diagrams

A liquid boils when its vapor pressure equals the external pressure. Clausius–Clapeyron: ln(P2/P1) = (ΔHvap/R)(1/T1 − 1/T2). On a phase diagram the lines are equilibria, the triple point is where all three phases coexist, and beyond the critical point there is a supercritical fluid.

Worked example. Water has ΔHvap = 40.7 kJ/mol and boils at 373 K at 1 atm. At 363 K: ln(P2/760) = (40700/8.314)(1/373 − 1/363) = −0.364, so P2 = 528 torr.

Want to see it happen first? Open PhaseLabs: add heat to water and watch the heating curve, the plateaus and every step's heat.

Step 8. Solids and unit cells

Cubic unit cells: simple cubic has 1 atom, body-centered has 2, face-centered has 4. Edge length a is related to atomic radius r by a = 2r (sc), 4r = a√3 (bcc), 4r = a√2 (fcc). Density: d = ZM ÷ (NA a3) with a in cm.

Worked example. Copper is fcc with a = 361.5 pm: d = 4 × 63.55 ÷ (6.022 × 1023 × (3.615 × 10−8 cm)3) = 8.93 g/cm3.

Practice gases, liquids and solids

PhaseWorks is part of Track 1 (General Chemistry I) of ChemTracks. Each topic has a short lesson, a practice tab with three levels of randomly generated problems, hints and worked solutions, and a crown for mastering it. Earn every crown for a certificate.

Topics covered

Frequently asked questions

What does PhaseWorks cover in General Chemistry I?

Gas laws, the ideal gas law, gas stoichiometry, partial pressures, kinetic molecular theory and real gases, intermolecular forces, vapor pressure and phase diagrams, and solids and unit cells.

How is this different from Track 0 GasWorks?

Track 0 GasWorks introduces the basic gas laws. This Track 1 page adds the full ideal gas law, gas stoichiometry, kinetic theory, liquids and solids.

Do I get a certificate?

Yes. Earn every crown in this Works and you can claim a free certificate of completion as a PDF.

Do I need an account to use PhaseWorks?

No. It runs in your browser and saves your progress on your own device.

More Track 1 practice